Multi-Recorder Measurement Unit(TMR-300 Series) Strain Full Bridge Unit TMR-321

Strain Full Bridge Unit TMR-321CE

This unit is for measurement of strain in full bridge connection. Measurement of DC voltage is also possible by using optional attenuator cable (CR-4010).

Strain Full Bridge Unit TMR-321

  • Specifications
    Type TMR-321
    Number of measuring points 8 channels
    Input Strain, Voltage (when using optional cable CR-4010)
    Applicable gauge resistance 120 to 1000 Ω
    Bridge excitation DC 0.5 V, 2 V
    Measuring range ±20000 x 10-6 strain (bridge excitation 2 V)
    ±80000 x 10-6 strain (bridge excitation 0.5 V)
    External dimensions 200(W) x 25(H) x 100(D) mm (excluding projected parts)
    Weight Approx. 550 g (including rubber protectors)
    Power supply DC 10 V to 30 V 0.2 A at maximum (12 V) (supplied from TMR-311)

More Information

Dynamic Strainmeters Analog type Carrier type Dynamic Strainmeter DA-38A

Carrier type Dynamic Strainmeter DA-38A

The DA-38A is a carrier wave type dynamic strainmeter with high frequency response of 10 kHz. It features easy operation and excellent noise resistivity. Digital sensitivity setting method is adopted to enable easy and accurate setting. Also provided is digital display function of measurement value for reliable dynamic measurement. One unit is for one measurement channel, and two or more units can be installed in an exclusive case or rack to make a multi-channel system.

Carrier type Dynamic Strainmeter DA-38A
Features
  • Frequency response of DC to10 kHz
  • Carrier wave bridge excitation provides excellent resistivity to noise
  • Always checks disconnection of strain gauges and cable
  • Two output monitors provided; Digital display and level meter
  • Lower power consumption compared to conventional models
  • Automatic tracking capacity balancing
  • Reading and automatic setting of TEDS transducer
  • Dual output
  • Built-in low-pass filter
  • Possible external control for balancing and calibration signal output

  • Specifications
    Type DA-38A
    Measuring object Strain
    Number of channels 1 channel
    Measuring range

    ±50000 x 10-6 strain
    Frequency response DC to 10 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight Approx. 750 g
    Power supply AC 90 to 264 V 50 / 60 Hz 8.5 VA MAX. (AC100 V)
    DC 10 to 30 V 0.27 A MAX. (DC12 V)

More Information

Dynamic Strainmeters Analog type Carrier type Dynamic Strainmeter DA-18A

Carrier type Dynamic Strainmeter DA-18A

The DA-18A is a carrier wave type dynamic strainmeter featuring easy operation and excellent noise resistivity. Digital sensitivity setting method is adopted to enable easy and accurate setting. Also provided is digital display function of measurement value for reliable dynamic measurement. One unit is for one measurement channel, and two or more units can be installed in an exclusive case or rack to make a multi-channel system. 

Carrier type Dynamic Strainmeter DA-18A
Features
  • Frequency response of DC to 2.5 kHz
  • Carrier wave bridge excitation provides excellent resistivity to noise
  • Equipped with two output monitors; Digital display and level meter
  • Lower power consumption compared to conventional models
  • Automatic tracking capacity balancing
  • Reading and automatic setting of TEDS transducer
  • Dual output
  • Built-in low-pass filter
  • External control possible for balancing and calibration signal output

  • Specifications
    Type DA-18A
    Measuring object Strain
    Number of channels 1 channel
    Measuring range

    ±50000×10-6 strain
    Frequency response DC to 2.5 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight 870 g
    Power supply AC 90 to 110 V or 198 to 242 V 50 / 60 Hz 6 VA MAX. (AC100 V)
    DC 10 to 30 V 0.25 A MAX. (DC12 V)

More Information

Dynamic Strainmeters Analog type Carrier type Dynamic Strainmeter DA-37A

Carrier type Dynamic Strainmeter DA-37A

The DA-37A is a carrier wave type dynamic strainmeter with high frequency response of 10 kHz. One unit is for one measurement channel, and two or more units can be installed in an exclusive case or rack to make a multi-channel system.
By installing the units in the exclusive carrying case for computer control, control from a PC via LAN is possible such as settings of sensitivity and low pass filter, operation of balancing and calibration, and acquisition of setting and monitor values.

Carrier type Dynamic Strainmeter DA-37A
Features
  • High frequency response of DC to 10 kHz
  • Digital monitor of output voltage, with indication of maximum / minimum value and open / over
  • Electronic automatic balancing
  • Isolation between input and output
  • Automatic tracking capacity balancing
  • Dual output
  • Built-in low-pass filter
  • Insulation resistance check function for strain gauge bridge
  • External control possible for balancing and calibration signal output
  • Dual power supply of AC and DC
  • Possible control by PC (when installed in exclusive case)

  • Specifications
    Type DA-37A
    Measuring object Strain
    Number of channels 1 channel
    Measuring range

    ±50000×10-6 strain
    Frequency response DC to 10 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight Approx. 750 g
    Power supply AC 90 to 132 V 50 / 60 Hz 9.2 VA MAX. (AC100 V)
    DC 10 to 30 V 0.35 A MAX. (DC12 V)

More Information

Compression Load Cell CLG-NB

CLG-NB Compression Load Cell
10kN to 200kNCE

The CLG-NB Load Cell is a high precision load cell in a thin, hermetically sealed package. It is widely used in tight spaces and as a system sensor for industrial machinery.

Protection ratings : IP 67 equivalent

Compression Load Cell CLG-NB
Features
  • Hermetically sealed, High precision, High stability
  • Low profile, Easy to install
  • Most applicable as system sensor for industrial machines

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLG-10KNB 10kN 2mV/V
    (4000×10-6 strain) ±0.5 %    		 0.2 %RO -20 to +70 ℃
    CLG-20KNB 20kN
    CLG-50KNB 50kN
    CLG-100KNB 100kN
    CLG-200KNB 200kN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information

Dynamic Strainmeters Analog type Carrier type Dynamic Strainmeter DA-17A

Carrier type Dynamic Strainmeter DA-17A

The DA-17A is a carrier wave type dynamic strainmeter with frequency response of 2.5 kHz. One unit is for one measurement channel, and two or more units can be installed in an exclusive case or rack to make a multi-channel system. 
By installing the units in the exclusive carrying case for computer control, control from a PC via LAN is possible such as setting of sensitivity and low pass filter, operation of balancing and calibration, and acquisition of setting and monitor values.

Carrier type Dynamic Strainmeter DA-17A
Features
  • Frequency response of DC to 2.5 kHz
  • Digital monitor of output voltage, with indication of maximum / minimum value and open / over
  • Electronic automatic balancing
  • Isolation between input and output
  • Automatic tracking capacity balancing
  • Peak hold function privided
  • Dual output
  • Built-in low-pass filter
  • Insulation resistance check function for strain gauge bridge
  • External control possible for balancing and calibration signal output
  • Dual power supply of AC and DC
  • Possible control by PC (when installed in exclusive case)

  • Specifications
    Type DA-17A
    Measuring object Strain
    Number of channels 1 channel
    Measuring range

    ±50000 x 10-6 strain
    Frequency response DC to 2.5 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight Approx. 870 g
    Power supply AC 90 to 132 V 50 / 60 Hz 7.5 VA MAX. (AC100 V)
    DC 10 to 30 V 0.25 A MAX. (DC12 V)

More Information

Compression Load Cell CLU-NA

CLU-NA Compression Load Cell
10kN to 1MNCE

The CLU-NA Load Cell is an inert-gas encased load cell in a hermetically sealed package. The strain sensing element has a simple structure that enables highly precise and consistent measurements over long periods of time.

Two independent output type is aslo available on request.

Protection ratings : IP 65 equivalent

Compression Load Cell CLU-NA
Features
  • Long-term stable measurement
  • Easy handling

  • Specifications
    Type Capacity Rated output Non-linearity Temperature
    range
    CLU-10KNA 10kN 2mV/V
    (4000×10-6 strain) ±0.2 %    		 0.15 %RO -30 to +80 ℃
    CLU-20KNA 20kN
    CLU-50KNA 50kN
    CLU-100KNA 100kN
    CLU-200KNA 200kN
    CLU-500KNA 500kN
    CLU-1MNA 1MN

    Output polarity

    Measurement moves in the minus direction with regard to increased compressing force.

More Information