Insertion Type Inclinometer

Insertion Type Inclinometer KB-GC/KB-HC　±5° to ±10°CE

This is the inclinometer that measures the displacement of the ground or structure.
A special guide pipe is installed vertically in the ground or structure in advance, and an inclinometer is inserted to measure the angle of inclination in the pipe to determine the amount of displacement.
It is used for measuring the displacement of landslides on landslides and the displacement of earth retaining walls.
The KB-HC model can also measure in the X and Y directions simultaneously.

Protection rating: IP68 equivalent

Insertion Type Inclinometer KB-GC/KB-HC
Features
  • Made of all stainless steel for excellent corrosion resistance
  • Excellent environmental resistance in the field
  • High reliability
  • Type KB-HC can measure in X and Y direction simultaneously

  • Specifications
    Type No. of measuring axis Capacity Rated output Non-linearity Temperature range
    KB-5GC 1 direction ±5° Approx. 1mV/V（2000x10-6 strain） 0.5％RO －20 to ＋60℃
    KB-10GC ±10°
    KB-5HC 2 directions ±5°
    KB-10HC ±10°

    Output polarity

    The measured value moves in the direction of the arrow on the label on the body of the unit in relation to the change in inclination.

More Information

CDP-B Splashproof High Sensitive Displacement Transducer

CDP-B Splashproof High Sensitive Displacement Transducer 5 to 25 mmCE

Displacement transducer with bellows mounted on the shaft of a CDP-type displacement transducer. Used for measurements in poor environmental conditions, e.g. on site.

Protection rantings : IP 42 equivalent

CDP-B Splashproof High Sensitive Displacement Transducer
Features
  • Excellent environmental resistance
  • High sensitivity, high power

  • Specifications
    Type Capacity Rated output Sensitivity(×10-6 strain/mm) Non-linearity Temperature range
    CDP-5B 5mm 5mV/V
    （10000×10－6strain）
    ±0.1%    		 2000 0.15％RO －10～＋60℃
    （no condensation）
    CDP-10B 10mm 5mV/V
    （10000×10－6strain）
    ±0.1%    		 1000 0.1％RO
    CDP-25B 25mm 6.25mV/V
    （12500×10－6strain）
    ±0.1%    		 500

    Output polarity

    img-trout-01-2

    Measurement moves in the minus direction when the shaft is pushed inward.

More Information

DC type Dynamic Strainmeter DC-96A/DC-97A

DC type Dynamic Strainmeter DC-96A/DC-97A

This is a dynamic strainmeter that uses direct current as the bridge power supply. 
The bridge power supply can be selected from constant voltage or constant current type. 
In the constant-current type, there is no sensitivity reduction due to the resistance of the connecting cable between the strain gage transducer and the bridge box. 
The instrument can be built into a dedicated case or rack for multi-channel configuration.

DC type Dynamic Strainmeter DC-96A/DC-97A
Features
  • Broadband response frequency
    DC-96A: DC to 200 kHz, DC-97A: DC to 500 kHz 
  • Digital sensitivity setting method 
  • Electronic auto-balance 
  • Temperature stability of the zero point is as high as 0.5×10-6 strain/°C 
  • Can be used as a DC amplifier 
  • Bridge power supply switchable between constant voltage and constant current 
  • Dual output system 
  • Built-in low-pass filter and high-pass filter 
  • Strain bridge insulation check function 
  • External control of balanced and calibrated outputs possible 
  • AC and DC dual power supply system 

  • Specifications
    Type DC-96A DC-97A
    Measuring object Strain gauge, strain gauge transducer 
    DC voltage
    Number of channels 1 channel
    Measuring range ±100000×10-6strain
    (Gauge rate fixed at 2.00)
    Voltage measuring range ±100 mV
    Frequency response DC to 200 kHz DC to 500 kHz
    External dimensions 40(W) x 140(H) x 266(D) mm
    Weight Approx. 1.2 kg
    Power supply AC 90 to 132V 50/60Hz 16VA MAX. 
    AC 180 to 250V 50/60Hz 16VA MAX. 
    (Based on any of the instructions) 
    DC 10-30V 0.7A MAX.

More Information

High Temperature Use Strain Gauge EF Series

High Temperature Use Strain Gauge EF Series

These gauges have a small grid pattern required for measurement of printed circuit boards and surface mounted devices, which are getting smaller and smaller. The backing of the gauges is made of polyimide resin. The maximum operaing temperature is +300℃ for single element gauges and +200℃ for two and three elements gauges. The lowest operating temperature is -196℃ for both gauges.

EF Series High Temperature Strain Gauges
Applicable specimen Metal, Composite material
Operational temperature EFLK/EFLX: -196 to +300℃
EFCA/EFRA: -196 to +200℃
Temperature compensation range EFLK/EFLX: +10 to +150℃
EFCA/EFRA: 0 to +150℃
Applicable adhesive CN, EB-2, NP-50B, C-1
Backing Polyimide
Element Ni-Cr
Strain limit 1% (10000 x 10-6 strain)
Fatigue life at room temperature 1 x 106(±1500 x 10-6 strain)

  • Single-elementCE
    Gauge pattern Type

    Gauge
    length
    (mm)

    Gauge
    width
    (mm)

    Backing
    length
    (mm)

    Backing
    width
    (mm)

    		 Resistance (Ω)
    eflk_02
    EFLK-02    		 EFLK-02-11 0.2 0.8 1.6 1.2 120
    eflx_02
    EFLX-02    		 EFLX-02-11 0.2 0.8 1.8 1.2 120

    Each package contains 10 gauges.

  • two-element / three-element
    Gauge pattern Type Gauge
    length
    (mm)    		 Gauge
    width
    (mm)    		 Backing
    length
    (mm)    		 Backing
    width
    (mm)    		 Resistance (Ω)
    img_efra_05
    EFRA-05    		 EFCA-05-11 0.5 0.4 φ3.8 120
    EFRA-05-11 0.5 0.4 φ3.8 120

    Each package contains 10 gauges.

More Information

Multi-Recorder Measurement Unit(TMR-300 Series) Voltage output Unit TMR-341

Voltage output Unit TMR-341CE

Conversion and output of data in analog voltage for strain, temperature, etc. measured by other units

電圧出力ユニット TMR-341

  • Specifications
    Type TMR-341
    Number of measuring points 8 channels
    Output signal Voltage output of measured data obtained by other measurement unit 
    (measurement point for output can be set optionally)
    Output of the result of accumulation or subtraction of up to 4 points
    Output level ±10V, ±5V, 0 ~ +5V (5kΩ load)
    External dimensions 200(W) × 25(H) × 100(D)mm
    Weight Approx. 550 g (including rubber protectors)
    Power supply DC 10 ~ 30V, 0.3A at maximum (12V)(supplied from TMR-311)

More Information